ENGINEER TALKS Ep.41: Bolt Holes in Marine Hardware: Edge Distance, Bearing Stress and Hole Elongation

● 2026-11-16 ● - ● Leave me a message

At Andy Marine, we believe that practical manufacturing knowledge is one of the most valuable assets built over time.

Inside our workshop, there are engineers, production specialists, and experienced technicians who have spent years working with stainless steel marine hardware — from material selection and casting processes to finishing and quality control.

Many of these insights are learned through daily production experience: understanding why a component fails, how different materials perform in marine environments, and what details truly matter when developing reliable hardware.

However, this practical knowledge is often shared only within the workshop and rarely reaches customers who are making sourcing and engineering decisions.

ENGINEER TALKS is our effort to organize these conversations and share the manufacturing experience behind marine hardware.

Through this series, we discuss materials, production processes, design considerations, and real-world lessons from the perspective of a marine hardware manufacturer.

Today's ENGINEER TALKS Ep.41 is presented by Engineer Wu, written by me the editor.

Two Returned Bases, Two Directions of Wear

Suppose two cleat bases come back from service — a hypothetical, not a customer file — both with holes no longer round, both reported by the yard as loose bolts.

On the bench the difference is at the holes. The first shows elongation along the line of pull, with red-brown powder around the rim. The second shows marks at an angle to the load, and one hole polished in a crescent its neighbour does not share.

Same complaint, two histories. The yard described how the bolts felt under a spanner, not what the joint did over the seasons — and a hole carries a record of movement with several authors: a design that left too little material, an installation that never held the joint closed, a casting never sound where the hole went.

A Hole Is a Clearance, and Movement Comes First

A clearance hole is what its name says. The shank passes through an opening larger than itself, and until the clamped faces slide far enough for it to reach the far wall, the fastener carries no shear. Load crosses the interface as friction from the clamp, or the joint moves.

So a base on clearance holes is not rigid in shear. With four bolts the bolt closest to its hole wall loads first and must yield before the next shares, so by the time the fourth is working, the first has been somewhere it was never designed to go.

That separates two things the yard's phrase merges. A bolt that feels loose may never have loosened: the joint may have been held by clamp alone, and once that clamp was gone — see the episode on why marine hardware bolts loosen — the holes carried the movement instead of the interface.

Then the Load Arrives on a Small Patch

Once the shank does touch, the contact is nothing like a bolt filling its hole. Load passes through a small patch: the width of the hole against the thickness of the material. That is bearing stress — a crushing condition at the hole wall, not a stress spread evenly across the base.

The area doing the work is small, so what happens is decided locally: a base that looks substantial in the middle can be marginal at a hole if the wall is thin there. And thickness is half the patch — a bigger bolt brings a bigger hole, so the patch grows with diameter while the material behind it does not.

What the base does with that load afterwards — backing plate, bedding, the route into the deck — belongs to the episode on boat cleat installation.

Move the Hole and the Failure Changes Shape

Move the hole toward an edge and a different mechanism takes over. There is no longer enough material for the wall to carry load in compression; the strip between hole and free edge is pushed out ahead of the bolt, shearing along two planes. What leaves is a plug of material — tear-out — and the area resisting is that strip, so it grows with distance to the edge and with thickness.

Edge distance is therefore a design quantity, not a layout preference.

Published rules exist, and one is worth reading for its shape. European structural steelwork practice, in BS EN 1993-1-8 Table 3.3, sets minimum end and edge distances of 1.2 times the hole diameter from the hole centre. The same table sets a maximum of 4t + 40 mm, t being the thickness of the thinner connected part, because on exposed steelwork an over-long edge invites corrosion and buckling of the outstanding material. A minimum quoted without its ceiling is half a rule.

That is a rule for bolted plate in buildings: not a marine requirement, not a casting rule. A cast lug carries draft, a fillet where the boss meets the body and a profile that follows the mould rather than the load; the flat-plate picture does not transfer by arithmetic. What transfers is the reasoning — more helps up to a point, and past it the problem has moved elsewhere.

How a Round Hole Becomes a Slot

An elongated hole is rarely the product of one overload but of many small movements, none of which anyone present would have called movement.

Fretting needs only micro-slip, far below what the eye registers. Two surfaces held together under load, with the smallest relative oscillation, micro-weld at high points and tear apart; the debris oxidises to a red-brown powder that occupies space. The joint opens by the thickness of the powder, movement grows, more powder forms — which is why a hole round at commissioning can be visibly oval at the first refit.

Hole-making joins the same loop. A punched hole carries a slight cone and a worked, damaged edge; a drilled or reamed one does not, and the difference counts for more while the joint is loose than after it is properly clamped.

Then the seat. A washer over a slotted or oversized hole has to stay flat; a thin one dishes into the opening, bears on a ring at the hole edge instead of spreading load, and loses the clamp the joint needed. A cast face is not a machined face either: where a head must sit flat, the answer is a local machined pad, so the seat is a controlled surface rather than what the mould left.

Reading a Cracked Lug

The material between hole and edge can shear out. A crack can start at the hole, because a hole interrupts the material and a stress concentration is what a hole is; whether it does depends on how the joint was loaded and how well it stayed clamped. And the boss can have been unsound before either happened — a boss is added material, added material is where a casting solidifies last, and that is where shrinkage porosity can sit. The crack and the unsound casting can be one story read from two ends.

The crack does not separate them. It is a fact about the outcome, not the cause.

What moves the question forward is a sequence of checks, none needing a laboratory: where the crack runs, and whether it heads for the free edge or starts at the far side of the hole from the load; whether the joint shows any sign of being clamped, from a washer impression to paint undisturbed under the head; whether the hole is within the series the drawing called for and where the drawing put it; whether the seat is flat and full; and what the records say, since a batch card that shows nothing is itself a finding.

The list gets shorter, not resolved. A hole may have been oversize from new and the crack may still be a fatigue crack from a joint that lost clamp in service. Staining and powder establish that the joint was moving. They do not establish why.

What Belongs in the Specification and the Goods-In Check

Hole size first: a clearance hole is a choice from a table, not a size the shop settles on the day. The standard offers fine, medium and coarse series rather than one diameter per thread, and which series applies is a design decision — a drawing that says clearance and stops there hands the choice to whoever is at the drill.

Edge distance second, as a requirement with its basis named, so nobody later lifts a building-steel ratio onto a casting. Take a deck cleat: what matters is the material between fastener and edge. Seat condition third, written down rather than left to the pattern. Hole-making fourth, because drilled, reamed or punched is a fatigue variable.

On delivery, four observations need no laboratory. Are the holes round, and where the drawing puts them? Run a fingertip round each edge: burr, cone, torn lip? Is there a machined pad at the seat, flat and full? And check the hole against the series called for, not against the bolt: a bolt will pass through a hole well outside the series called for.

Observation at the hole What it establishes What it still leaves open
Elongation along the load direction, with oxide staining The joint moved in service Whether it moved because clamp was lost, or because the hole was always oversize
Crack running from the hole to the free edge The ligament between hole and edge was loaded in shear Whether the material there was sound when the crack started
Polished or dished seat, washer impression under the head The head never sat flat, or the clamp was low Whether that came from the casting, the machining or the assembly
Hole larger than the drawing series, or off position The part was not built as specified Whether that is what caused the failure

Send Inquiry

X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
Reject Accept